Digital Dash Project based on STM32 MCU and TOUCHGFX

[Omen234]

IMG_3541.jpeg (3.14 MiB) Viewed 54255 times

IMG_3546.jpeg (2.88 MiB) Viewed 54255 times

IMG_3548.jpeg (3.06 MiB) Viewed 54255 times

[Omen234]

here is the link to the repository
https://github.com/romioRN/Dash_st800

[Omen234]

[AndreyB]

I see a starting rope, does it start from the rope?

[mi-hol]

here is the link to the repository
https://github.com/romioRN/Dash_st800

the link gives a 404 not found error. Is it a public repository?

[Omen234]

Try again

[mi-hol]

Thanks, works now

[Omen234]

added an eprom and returned an ESP32

[Omen234]

IMG_4190.jpeg (3.59 MiB) Viewed 48156 times

IMG_4190.jpeg (3.59 MiB) Viewed 48156 times

IMG_4191.jpeg (3.34 MiB) Viewed 48156 times

[Omen234]

добавил репозиторий с кодом
https://github.com/romioRN/Dash6.8_firmware

[Omen234]

IMG_4414.png (167.96 KiB) Viewed 46146 times

[Omen234]

Снимок экрана (31).png (209.51 KiB) Viewed 46129 times

we made an ESP32 server with a test engine monitoring page

[Omen234]

updated the case again

Снимок экрана (4).png (685.65 KiB) Viewed 46129 times

[Omen234]

https://github.com/romioRN/Dash_st800/tree/main/silicone%20casting
link to the new dashboard housing

[Omen234]

Снимок экрана (35).png (222.26 KiB) Viewed 45996 times

Снимок экрана (34).png (451.13 KiB) Viewed 45996 times

[itsrealfast]

Hi,

I downloaded the github files but I dont see the latest version with ESP32. Is it possible if you can upload it? Do you have the updated firmware?

I am planning ordering pcb and components. The goal would be to adapt it on my Yamaha jetski

Please let me know

Thanks

[Omen234]

I'll update the repository later. I'm adding the USART exchange protocol. Hopefully it won't take too long. I plan to do it in a week and then how will it turn out

[Omen234]

updated the firmware and the board

https://github.com/romioRN/Dash_6.8-hardware
https://github.com/romioRN/Dash6.8_firmware

[Enigma2023]

There is still an issue with ~$рама платы L.SLDPRT not working in solid works nor fusion 360. Can you provide updated file?

[bgd_c66]

IMG_3541.jpegIMG_3546.jpegIMG_3548.jpeg

Hello,
Found this forum while searching for a digital dash for my nissan patrol, which has analog gauges, and immediately thought that it's what i need .
I can gather the analog signals and send them through CAN bus to this dashboard.
From your perspective ,i can build the hardware, is the software difficult to understand for a beginner ?
Is my idea ,of converting the analog data to can, even going to work with this digital dash??

[Omen234]

There is still an issue with ~$рама платы L.SLDPRT not working in solid works nor fusion 360. Can you provide updated file?

https://github.com/romioRN/Dash_6.8-hardware/blob/main/3d%20model/silicone%20casting/рама%20платы%20L.STEP

Снимок экрана (52).png (536.4 KiB) Viewed 28965 times

added the STEP files. If you want to open it in SolidWorks, you need a version not lower than 2024 SP5.0

[Omen234]

updated the firmware and the board

https://github.com/romioRN/Dash_6.8-hardware
https://github.com/romioRN/Dash6.8_firmware

updated the board firmware and 3D models

[Omen234]

IMG_3541.jpegIMG_3546.jpegIMG_3548.jpeg

Hello,
Found this forum while searching for a digital dash for my nissan patrol, which has analog gauges, and immediately thought that it's what i need .
I can gather the analog signals and send them through CAN bus to this dashboard.
From your perspective ,i can build the hardware, is the software difficult to understand for a beginner ?
Is my idea ,of converting the analog data to can, even going to work with this digital dash??

I think you should be able to do it because I'm a beginner too. the code is not very complicated yet and seems to be more or less understandable . CAN reception without any problems

[Enigma2023]

There is still an issue with ~$рама платы L.SLDPRT not working in solid works nor fusion 360. Can you provide updated file?

https://github.com/romioRN/Dash_6.8-hardware/blob/main/3d%20model/silicone%20casting/рама%20платы%20L.STEP
Снимок экрана (52).png
added the STEP files. If you want to open it in SolidWorks, you need a version not lower than 2024 SP5.0

Thank you. I was able to use this version in Fusion 360.