rusefi.com

or map sensor in case of odd-fire engine

cam sensor

You are asking how to route an auxiliary analog input channel.

Does not seem to be routed to main 76 pin header but a couple of pins are available on the ETB upgrade option

Please use TPS2 or PPS1

also https://github.com/rusefi/rusefi/wiki/AlphaX-Silver

Polaris is more or less the same thing, just totally different.

53 inches seems to be the perfect length if you need to do the same.

TCU protocol reverse engineering progress: I think I've located numeric torque reduction request byte, green on the chart
Also random link https://nissanecu.miraheze.org/wiki/Nissan_Tuning

Without knowing engine phase engine is running in wasted spark mode.

Welcome to the forum!

Well, that kinda works David says: Any 8 or 10 speed is going to be a clutch-to-clutch transmission, which is very much not supported currently. Oversimplification: A clutch-to-clutch transmission has a solenoid for each clutch, including torque converter clutch. An old fashioned transmission has s...

Active Dumper System, the less fancy one without stroke sensors like on Civic Type R.

Why do they run two dedicated wires to each strut solenoid? Why not shared high side?

Appreciate the write up!

coolantbongrips wrote: ↑

Wed May 15, 2024 2:19 am

Is there an official value for this resistor, or does it have to be found through experimentation?

https://github.com/rusefi/uaefi/issues/65

Добрый вечер let me recommend https://github.com/rusefi/rusefi/wiki/Discord

Zero relation between vvt outputs and sycn.

Please https://github.com/rusefi/rusefi/wiki/rusEFI-Quick-Start-PDF#log-it and https://github.com/rusefi/rusefi/wiki/rusEFI-Quick-Start-PDF#share-it

TODO support MAF sensors like 04E906051 see https://github.com/rusefi/rusefi-hardware/issues/146

Yes but you would have to use "blend" tables feature - it's powerful but complicated.

VE is insane, that often means that injector dead times are wrong.

let me point you at part of your tune responsible for VTEC control https://rusefi.com/online/view.php?msq=1652&dialog=gppwm1

ZayTuned wrote: ↑

Sun May 12, 2024 5:01 pm

I had my trigger wired to the discrete VR and its supposed to go to the 9924 VR

Your choice not to search for existing threads on obd1.

It has a 24 tooth wheel for the trigger rpm signal in the distributor and another wheel that has 4 teeth for sync. Would it be safe to assume that you did not hit "OBD1" preset and probably have wrong trigger setup? See also https://github.com/rusefi/rusefi/wiki/All-Supported-Triggers#12-...

Hold on, does this vehicle have THREE separate CAN buses?!

https://github.com/rusefi/rusefi_documentation/blob/master/OEM-Docs/Honda/2021-Acura-RDX-data-lines.pdf

Power steering uses one bus but electronic gear shifter uses two? Two buses between ECU and ECU?

Many years ago I had a not so bright orange vehicle with a Honda K engine. It has blown the head gasket for not good reason :( So I've decided to purchase a bright orange vehicle, again with Honda K engine, this time GDI and turbo-charged! And Acura Care Extended Warranty :) WhatsApp Image 2024-05-0...

it's usually one resistor away working, just an open question if that's a pull-up or a pull-down and what value maybe try a few combinations?

are you trying low side or high side output?

Consider asking at the rusEFI discord server

this has definitely turned to be way more work than I anticipated

Alexey @vag0dr04er has contributed _something_ - right now it's available in Proteus firmware, let me see if I can also enable it for 4chan and uaefi

https://github.com/rusefi/rusefi/pull/6467

Any MAP and throw MAF away. Bosch 4 pin TMAPs with integrated IAT are a popular option

rusEFI has "ford/toyota" redundant TPS and PPS modes that's what you are looking for

What if your oil pressure sensor breaks while you are turning? You would have to use Lua for this safety feature.

gurov wrote: ↑

Thu May 02, 2024 4:34 pm

However, stm32f407vEt won't do for our purposes

Well, _technically_ we have provisions to persist calibrations on external SPI flash and that mega board has it! There is a chance to run rusEFI stm32f407vE maybe without Lua maybe with Lua.

https://github.com/rusefi/rusefi/issues/6452
https://github.com/rusefi/rusefi/commit/9cb308b09d569e2bdf5bd1a26c8d0448fdfc7067

https://github.com/rusefi/rusefi/commit/ec50d034bc858a3e34f327df0058912d3710e171 looks like rusEFI is gaining ability to actually use those aux outputs? And maybe those aux inputs soon?