rusEFI
The most advanced open source ECU
Loading...
Searching...
No Matches
stm32f7xx_hal_conf.h
Go to the documentation of this file.
1/**
2 ******************************************************************************
3 * @file stm32f7xx_hal_conf.h
4 * @brief HAL configuration file.
5 ******************************************************************************
6 * @attention
7 *
8 * <h2><center>&copy; COPYRIGHT(c) 2019 STMicroelectronics</center></h2>
9 *
10 * Redistribution and use in source and binary forms, with or without modification,
11 * are permitted provided that the following conditions are met:
12 * 1. Redistributions of source code must retain the above copyright notice,
13 * this list of conditions and the following disclaimer.
14 * 2. Redistributions in binary form must reproduce the above copyright notice,
15 * this list of conditions and the following disclaimer in the documentation
16 * and/or other materials provided with the distribution.
17 * 3. Neither the name of STMicroelectronics nor the names of its contributors
18 * may be used to endorse or promote products derived from this software
19 * without specific prior written permission.
20 *
21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
24 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
25 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
28 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
29 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31 *
32 ******************************************************************************
33 */
34
35/* Define to prevent recursive inclusion -------------------------------------*/
36#ifndef __STM32F7xx_HAL_CONF_H
37#define __STM32F7xx_HAL_CONF_H
38
39#ifdef __cplusplus
40 extern "C" {
41#endif
42
43/* Exported types ------------------------------------------------------------*/
44/* Exported constants --------------------------------------------------------*/
45
46/* ########################## Module Selection ############################## */
47/**
48 * @brief This is the list of modules to be used in the HAL driver
49 */
50#define HAL_MODULE_ENABLED
51
52/* #define HAL_ADC_MODULE_ENABLED */
53/* #define HAL_CRYP_MODULE_ENABLED */
54#define HAL_CAN_MODULE_ENABLED
55/* #define HAL_CEC_MODULE_ENABLED */
56/* #define HAL_CRC_MODULE_ENABLED */
57/* #define HAL_CRYP_MODULE_ENABLED */
58/* #define HAL_DAC_MODULE_ENABLED */
59/* #define HAL_DCMI_MODULE_ENABLED */
60/* #define HAL_DMA2D_MODULE_ENABLED */
61/* #define HAL_ETH_MODULE_ENABLED */
62/* #define HAL_NAND_MODULE_ENABLED */
63/* #define HAL_NOR_MODULE_ENABLED */
64/* #define HAL_SRAM_MODULE_ENABLED */
65/* #define HAL_SDRAM_MODULE_ENABLED */
66/* #define HAL_HASH_MODULE_ENABLED */
67/* #define HAL_I2S_MODULE_ENABLED */
68/* #define HAL_IWDG_MODULE_ENABLED */
69/* #define HAL_LPTIM_MODULE_ENABLED */
70/* #define HAL_LTDC_MODULE_ENABLED */
71/* #define HAL_QSPI_MODULE_ENABLED */
72/* #define HAL_RNG_MODULE_ENABLED */
73/* #define HAL_RTC_MODULE_ENABLED */
74/* #define HAL_SAI_MODULE_ENABLED */
75/* #define HAL_SD_MODULE_ENABLED */
76/* #define HAL_MMC_MODULE_ENABLED */
77/* #define HAL_SPDIFRX_MODULE_ENABLED */
78/* #define HAL_SPI_MODULE_ENABLED */
79/* #define HAL_TIM_MODULE_ENABLED */
80/* #define HAL_UART_MODULE_ENABLED */
81/* #define HAL_USART_MODULE_ENABLED */
82/* #define HAL_IRDA_MODULE_ENABLED */
83/* #define HAL_SMARTCARD_MODULE_ENABLED */
84/* #define HAL_WWDG_MODULE_ENABLED */
85#define HAL_PCD_MODULE_ENABLED
86/* #define HAL_HCD_MODULE_ENABLED */
87/* #define HAL_DFSDM_MODULE_ENABLED */
88/* #define HAL_DSI_MODULE_ENABLED */
89/* #define HAL_JPEG_MODULE_ENABLED */
90/* #define HAL_MDIOS_MODULE_ENABLED */
91/* #define HAL_SMBUS_MODULE_ENABLED */
92/* #define HAL_MMC_MODULE_ENABLED */
93/* #define HAL_EXTI_MODULE_ENABLED */
94#define HAL_GPIO_MODULE_ENABLED
95#define HAL_DMA_MODULE_ENABLED
96#define HAL_RCC_MODULE_ENABLED
97#define HAL_FLASH_MODULE_ENABLED
98#define HAL_PWR_MODULE_ENABLED
99#define HAL_I2C_MODULE_ENABLED
100#define HAL_CORTEX_MODULE_ENABLED
101
102/* ########################## HSE/HSI Values adaptation ##################### */
103/**
104 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
105 * This value is used by the RCC HAL module to compute the system frequency
106 * (when HSE is used as system clock source, directly or through the PLL).
107 */
108/* No default! Should be explictly defined in openblt/board.mk */
109#if 0
110#if !defined (HSE_VALUE)
111 #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */
112#endif /* HSE_VALUE */
113#endif
114
115#if !defined (HSE_STARTUP_TIMEOUT)
116 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */
117#endif /* HSE_STARTUP_TIMEOUT */
118
119/**
120 * @brief Internal High Speed oscillator (HSI) value.
121 * This value is used by the RCC HAL module to compute the system frequency
122 * (when HSI is used as system clock source, directly or through the PLL).
123 */
124#if !defined (HSI_VALUE)
125 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
126#endif /* HSI_VALUE */
127
128/**
129 * @brief Internal Low Speed oscillator (LSI) value.
130 */
131#if !defined (LSI_VALUE)
132 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/
133#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
134 The real value may vary depending on the variations
135 in voltage and temperature. */
136/**
137 * @brief External Low Speed oscillator (LSE) value.
138 */
139#if !defined (LSE_VALUE)
140 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */
141#endif /* LSE_VALUE */
142
143#if !defined (LSE_STARTUP_TIMEOUT)
144 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
145#endif /* LSE_STARTUP_TIMEOUT */
146
147/**
148 * @brief External clock source for I2S peripheral
149 * This value is used by the I2S HAL module to compute the I2S clock source
150 * frequency, this source is inserted directly through I2S_CKIN pad.
151 */
152#if !defined (EXTERNAL_CLOCK_VALUE)
153 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
154#endif /* EXTERNAL_CLOCK_VALUE */
155
156/* Tip: To avoid modifying this file each time you need to use different HSE,
157 === you can define the HSE value in your toolchain compiler preprocessor. */
158
159/* ########################### System Configuration ######################### */
160/**
161 * @brief This is the HAL system configuration section
162 */
163#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
164#define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */
165#define USE_RTOS 0U
166#define PREFETCH_ENABLE 0U
167#define ART_ACCLERATOR_ENABLE 0U /* To enable instruction cache and prefetch */
168
169/* ########################## Assert Selection ############################## */
170/**
171 * @brief Uncomment the line below to expanse the "assert_param" macro in the
172 * HAL drivers code
173 */
174/* #define USE_FULL_ASSERT 1U */
175
176/* ################## Ethernet peripheral configuration ##################### */
177
178/* Section 1 : Ethernet peripheral configuration */
179
180/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
181#define MAC_ADDR0 2U
182#define MAC_ADDR1 0U
183#define MAC_ADDR2 0U
184#define MAC_ADDR3 0U
185#define MAC_ADDR4 0U
186#define MAC_ADDR5 0U
187
188/* Definition of the Ethernet driver buffers size and count */
189#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
190#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
191#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
192#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
193
194/* Section 2: PHY configuration section */
195
196/* LAN8742A_PHY_ADDRESS Address*/
197#define LAN8742A_PHY_ADDRESS 0
198/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
199#define PHY_RESET_DELAY ((uint32_t)0x000000FFU)
200/* PHY Configuration delay */
201#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU)
202
203#define PHY_READ_TO ((uint32_t)0x0000FFFFU)
204#define PHY_WRITE_TO ((uint32_t)0x0000FFFFU)
205
206/* Section 3: Common PHY Registers */
207
208#define PHY_BCR ((uint16_t)0x00U) /*!< Transceiver Basic Control Register */
209#define PHY_BSR ((uint16_t)0x01U) /*!< Transceiver Basic Status Register */
210
211#define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */
212#define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */
213#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */
214#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */
215#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */
216#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */
217#define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */
218#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */
219#define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */
220#define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */
221
222#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */
223#define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */
224#define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */
225
226/* Section 4: Extended PHY Registers */
227#define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */
228
229#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */
230#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */
231
232#define PHY_ISFR ((uint16_t)0x000BU) /*!< PHY Interrupt Source Flag register Offset */
233#define PHY_ISFR_INT4 ((uint16_t)0x000BU) /*!< PHY Link down inturrupt */
234
235/* ################## SPI peripheral configuration ########################## */
236
237/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
238* Activated: CRC code is present inside driver
239* Deactivated: CRC code cleaned from driver
240*/
241
242#define USE_SPI_CRC 0U
243
244/* Includes ------------------------------------------------------------------*/
245/**
246 * @brief Include module's header file
247 */
248
249#ifdef HAL_RCC_MODULE_ENABLED
250 #include "stm32f7xx_hal_rcc.h"
251#endif /* HAL_RCC_MODULE_ENABLED */
252
253#ifdef HAL_EXTI_MODULE_ENABLED
254 #include "stm32f7xx_hal_exti.h"
255#endif /* HAL_EXTI_MODULE_ENABLED */
256
257#ifdef HAL_GPIO_MODULE_ENABLED
258 #include "stm32f7xx_hal_gpio.h"
259#endif /* HAL_GPIO_MODULE_ENABLED */
260
261#ifdef HAL_DMA_MODULE_ENABLED
262 #include "stm32f7xx_hal_dma.h"
263#endif /* HAL_DMA_MODULE_ENABLED */
264
265#ifdef HAL_CORTEX_MODULE_ENABLED
266 #include "stm32f7xx_hal_cortex.h"
267#endif /* HAL_CORTEX_MODULE_ENABLED */
268
269#ifdef HAL_ADC_MODULE_ENABLED
270 #include "stm32f7xx_hal_adc.h"
271#endif /* HAL_ADC_MODULE_ENABLED */
272
273#ifdef HAL_CAN_MODULE_ENABLED
274 #include "stm32f7xx_hal_can.h"
275#endif /* HAL_CAN_MODULE_ENABLED */
276
277#ifdef HAL_CEC_MODULE_ENABLED
278 #include "stm32f7xx_hal_cec.h"
279#endif /* HAL_CEC_MODULE_ENABLED */
280
281#ifdef HAL_CRC_MODULE_ENABLED
282 #include "stm32f7xx_hal_crc.h"
283#endif /* HAL_CRC_MODULE_ENABLED */
284
285#ifdef HAL_CRYP_MODULE_ENABLED
286 #include "stm32f7xx_hal_cryp.h"
287#endif /* HAL_CRYP_MODULE_ENABLED */
288
289#ifdef HAL_DMA2D_MODULE_ENABLED
290 #include "stm32f7xx_hal_dma2d.h"
291#endif /* HAL_DMA2D_MODULE_ENABLED */
292
293#ifdef HAL_DAC_MODULE_ENABLED
294 #include "stm32f7xx_hal_dac.h"
295#endif /* HAL_DAC_MODULE_ENABLED */
296
297#ifdef HAL_DCMI_MODULE_ENABLED
298 #include "stm32f7xx_hal_dcmi.h"
299#endif /* HAL_DCMI_MODULE_ENABLED */
300
301#ifdef HAL_ETH_MODULE_ENABLED
302 #include "stm32f7xx_hal_eth.h"
303#endif /* HAL_ETH_MODULE_ENABLED */
304
305#ifdef HAL_FLASH_MODULE_ENABLED
306 #include "stm32f7xx_hal_flash.h"
307#endif /* HAL_FLASH_MODULE_ENABLED */
308
309#ifdef HAL_SRAM_MODULE_ENABLED
310 #include "stm32f7xx_hal_sram.h"
311#endif /* HAL_SRAM_MODULE_ENABLED */
312
313#ifdef HAL_NOR_MODULE_ENABLED
314 #include "stm32f7xx_hal_nor.h"
315#endif /* HAL_NOR_MODULE_ENABLED */
316
317#ifdef HAL_NAND_MODULE_ENABLED
318 #include "stm32f7xx_hal_nand.h"
319#endif /* HAL_NAND_MODULE_ENABLED */
320
321#ifdef HAL_SDRAM_MODULE_ENABLED
322 #include "stm32f7xx_hal_sdram.h"
323#endif /* HAL_SDRAM_MODULE_ENABLED */
324
325#ifdef HAL_HASH_MODULE_ENABLED
326 #include "stm32f7xx_hal_hash.h"
327#endif /* HAL_HASH_MODULE_ENABLED */
328
329#ifdef HAL_I2C_MODULE_ENABLED
330 #include "stm32f7xx_hal_i2c.h"
331#endif /* HAL_I2C_MODULE_ENABLED */
332
333#ifdef HAL_I2S_MODULE_ENABLED
334 #include "stm32f7xx_hal_i2s.h"
335#endif /* HAL_I2S_MODULE_ENABLED */
336
337#ifdef HAL_IWDG_MODULE_ENABLED
338 #include "stm32f7xx_hal_iwdg.h"
339#endif /* HAL_IWDG_MODULE_ENABLED */
340
341#ifdef HAL_LPTIM_MODULE_ENABLED
342 #include "stm32f7xx_hal_lptim.h"
343#endif /* HAL_LPTIM_MODULE_ENABLED */
344
345#ifdef HAL_LTDC_MODULE_ENABLED
346 #include "stm32f7xx_hal_ltdc.h"
347#endif /* HAL_LTDC_MODULE_ENABLED */
348
349#ifdef HAL_PWR_MODULE_ENABLED
350 #include "stm32f7xx_hal_pwr.h"
351#endif /* HAL_PWR_MODULE_ENABLED */
352
353#ifdef HAL_QSPI_MODULE_ENABLED
354 #include "stm32f7xx_hal_qspi.h"
355#endif /* HAL_QSPI_MODULE_ENABLED */
356
357#ifdef HAL_RNG_MODULE_ENABLED
358 #include "stm32f7xx_hal_rng.h"
359#endif /* HAL_RNG_MODULE_ENABLED */
360
361#ifdef HAL_RTC_MODULE_ENABLED
362 #include "stm32f7xx_hal_rtc.h"
363#endif /* HAL_RTC_MODULE_ENABLED */
364
365#ifdef HAL_SAI_MODULE_ENABLED
366 #include "stm32f7xx_hal_sai.h"
367#endif /* HAL_SAI_MODULE_ENABLED */
368
369#ifdef HAL_SD_MODULE_ENABLED
370 #include "stm32f7xx_hal_sd.h"
371#endif /* HAL_SD_MODULE_ENABLED */
372
373#ifdef HAL_MMC_MODULE_ENABLED
374 #include "stm32f7xx_hal_mmc.h"
375#endif /* HAL_MMC_MODULE_ENABLED */
376
377#ifdef HAL_SPDIFRX_MODULE_ENABLED
378 #include "stm32f7xx_hal_spdifrx.h"
379#endif /* HAL_SPDIFRX_MODULE_ENABLED */
380
381#ifdef HAL_SPI_MODULE_ENABLED
382 #include "stm32f7xx_hal_spi.h"
383#endif /* HAL_SPI_MODULE_ENABLED */
384
385#ifdef HAL_TIM_MODULE_ENABLED
386 #include "stm32f7xx_hal_tim.h"
387#endif /* HAL_TIM_MODULE_ENABLED */
388
389#ifdef HAL_UART_MODULE_ENABLED
390 #include "stm32f7xx_hal_uart.h"
391#endif /* HAL_UART_MODULE_ENABLED */
392
393#ifdef HAL_USART_MODULE_ENABLED
394 #include "stm32f7xx_hal_usart.h"
395#endif /* HAL_USART_MODULE_ENABLED */
396
397#ifdef HAL_IRDA_MODULE_ENABLED
398 #include "stm32f7xx_hal_irda.h"
399#endif /* HAL_IRDA_MODULE_ENABLED */
400
401#ifdef HAL_SMARTCARD_MODULE_ENABLED
402 #include "stm32f7xx_hal_smartcard.h"
403#endif /* HAL_SMARTCARD_MODULE_ENABLED */
404
405#ifdef HAL_WWDG_MODULE_ENABLED
406 #include "stm32f7xx_hal_wwdg.h"
407#endif /* HAL_WWDG_MODULE_ENABLED */
408
409#ifdef HAL_PCD_MODULE_ENABLED
410 #include "stm32f7xx_hal_pcd.h"
411#endif /* HAL_PCD_MODULE_ENABLED */
412
413#ifdef HAL_HCD_MODULE_ENABLED
414 #include "stm32f7xx_hal_hcd.h"
415#endif /* HAL_HCD_MODULE_ENABLED */
416
417#ifdef HAL_DFSDM_MODULE_ENABLED
418 #include "stm32f7xx_hal_dfsdm.h"
419#endif /* HAL_DFSDM_MODULE_ENABLED */
420
421#ifdef HAL_DSI_MODULE_ENABLED
422 #include "stm32f7xx_hal_dsi.h"
423#endif /* HAL_DSI_MODULE_ENABLED */
424
425#ifdef HAL_JPEG_MODULE_ENABLED
426 #include "stm32f7xx_hal_jpeg.h"
427#endif /* HAL_JPEG_MODULE_ENABLED */
428
429#ifdef HAL_MDIOS_MODULE_ENABLED
430 #include "stm32f7xx_hal_mdios.h"
431#endif /* HAL_MDIOS_MODULE_ENABLED */
432
433#ifdef HAL_SMBUS_MODULE_ENABLED
434 #include "stm32f7xx_hal_smbus.h"
435#endif /* HAL_SMBUS_MODULE_ENABLED */
436
437/* Exported macro ------------------------------------------------------------*/
438#ifdef USE_FULL_ASSERT
439/**
440 * @brief The assert_param macro is used for function's parameters check.
441 * @param expr: If expr is false, it calls assert_failed function
442 * which reports the name of the source file and the source
443 * line number of the call that failed.
444 * If expr is true, it returns no value.
445 * @retval None
446 */
447 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
448/* Exported functions ------------------------------------------------------- */
449 void assert_failed(uint8_t* file, uint32_t line);
450#else
451 #define assert_param(expr) ((void)0U)
452#endif /* USE_FULL_ASSERT */
453
454#ifdef __cplusplus
455}
456#endif
457
458#endif /* __STM32F7xx_HAL_CONF_H */
459
460
461/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
stm32f7xx_hal_flash.h
Header file of FLASH HAL module.
Generated on Sat Sep 27 2025 00:10:07 for rusEFI by doxygen 1.9.8