rusEFI
The most advanced open source ECU
Loading...
Searching...
No Matches
hw_layer
ports
stm32
stm32f4
openblt
lib
stm32f4xx_hal_conf.h
Go to the documentation of this file.
1
/**
2
******************************************************************************
3
* @file stm32f4xx_hal_conf_template.h
4
* @author MCD Application Team
5
* @brief HAL configuration template file.
6
* This file should be copied to the application folder and renamed
7
* to stm32f4xx_hal_conf.h.
8
******************************************************************************
9
* @attention
10
*
11
* <h2><center>© Copyright (c) 2017 STMicroelectronics.
12
* All rights reserved.</center></h2>
13
*
14
* This software component is licensed by ST under BSD 3-Clause license,
15
* the "License"; You may not use this file except in compliance with the
16
* License. You may obtain a copy of the License at:
17
* opensource.org/licenses/BSD-3-Clause
18
*
19
******************************************************************************
20
*/
21
22
/* Define to prevent recursive inclusion -------------------------------------*/
23
#ifndef __STM32F4xx_HAL_CONF_H
24
#define __STM32F4xx_HAL_CONF_H
25
26
#ifdef __cplusplus
27
extern
"C"
{
28
#endif
29
30
/* Exported types ------------------------------------------------------------*/
31
/* Exported constants --------------------------------------------------------*/
32
33
/* ########################## Module Selection ############################## */
34
/**
35
* @brief This is the list of modules to be used in the HAL driver
36
*/
37
#define HAL_MODULE_ENABLED
38
39
/* #define HAL_ADC_MODULE_ENABLED */
40
/* #define HAL_CRYP_MODULE_ENABLED */
41
#define HAL_CAN_MODULE_ENABLED
42
/* #define HAL_CRC_MODULE_ENABLED */
43
/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
44
/* #define HAL_CRYP_MODULE_ENABLED */
45
/* #define HAL_DAC_MODULE_ENABLED */
46
/* #define HAL_DCMI_MODULE_ENABLED */
47
/* #define HAL_DMA2D_MODULE_ENABLED */
48
/* #define HAL_ETH_MODULE_ENABLED */
49
/* #define HAL_NAND_MODULE_ENABLED */
50
/* #define HAL_NOR_MODULE_ENABLED */
51
/* #define HAL_PCCARD_MODULE_ENABLED */
52
/* #define HAL_SRAM_MODULE_ENABLED */
53
/* #define HAL_SDRAM_MODULE_ENABLED */
54
/* #define HAL_HASH_MODULE_ENABLED */
55
/* #define HAL_I2C_MODULE_ENABLED */
56
/* #define HAL_I2S_MODULE_ENABLED */
57
/* #define HAL_IWDG_MODULE_ENABLED */
58
/* #define HAL_LTDC_MODULE_ENABLED */
59
/* #define HAL_RNG_MODULE_ENABLED */
60
/* #define HAL_RTC_MODULE_ENABLED */
61
/* #define HAL_SAI_MODULE_ENABLED */
62
/* #define HAL_SD_MODULE_ENABLED */
63
/* #define HAL_MMC_MODULE_ENABLED */
64
/* #define HAL_SPI_MODULE_ENABLED */
65
/* #define HAL_TIM_MODULE_ENABLED */
66
/* #define HAL_UART_MODULE_ENABLED */
67
/* #define HAL_USART_MODULE_ENABLED */
68
/* #define HAL_IRDA_MODULE_ENABLED */
69
/* #define HAL_SMARTCARD_MODULE_ENABLED */
70
/* #define HAL_SMBUS_MODULE_ENABLED */
71
/* #define HAL_WWDG_MODULE_ENABLED */
72
#define HAL_PCD_MODULE_ENABLED
73
/* #define HAL_HCD_MODULE_ENABLED */
74
/* #define HAL_DSI_MODULE_ENABLED */
75
/* #define HAL_QSPI_MODULE_ENABLED */
76
/* #define HAL_QSPI_MODULE_ENABLED */
77
/* #define HAL_CEC_MODULE_ENABLED */
78
/* #define HAL_FMPI2C_MODULE_ENABLED */
79
/* #define HAL_SPDIFRX_MODULE_ENABLED */
80
/* #define HAL_DFSDM_MODULE_ENABLED */
81
/* #define HAL_LPTIM_MODULE_ENABLED */
82
#define HAL_GPIO_MODULE_ENABLED
83
#define HAL_EXTI_MODULE_ENABLED
84
#define HAL_DMA_MODULE_ENABLED
85
#define HAL_RCC_MODULE_ENABLED
86
#define HAL_FLASH_MODULE_ENABLED
87
#define HAL_PWR_MODULE_ENABLED
88
#define HAL_CORTEX_MODULE_ENABLED
89
90
/* ########################## HSE/HSI Values adaptation ##################### */
91
/**
92
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
93
* This value is used by the RCC HAL module to compute the system frequency
94
* (when HSE is used as system clock source, directly or through the PLL).
95
*/
96
/* No default! Should be explictly defined in openblt/board.mk */
97
#if 0
98
#if !defined (HSE_VALUE)
99
#define HSE_VALUE ((uint32_t)8000000U)
/*!< Value of the External oscillator in Hz */
100
#endif
/* HSE_VALUE */
101
#endif
102
103
#if !defined (HSE_STARTUP_TIMEOUT)
104
#define HSE_STARTUP_TIMEOUT ((uint32_t)100U)
/*!< Time out for HSE start up, in ms */
105
#endif
/* HSE_STARTUP_TIMEOUT */
106
107
/**
108
* @brief Internal High Speed oscillator (HSI) value.
109
* This value is used by the RCC HAL module to compute the system frequency
110
* (when HSI is used as system clock source, directly or through the PLL).
111
*/
112
#if !defined (HSI_VALUE)
113
#define HSI_VALUE ((uint32_t)16000000U)
/*!< Value of the Internal oscillator in Hz*/
114
#endif
/* HSI_VALUE */
115
116
/**
117
* @brief Internal Low Speed oscillator (LSI) value.
118
*/
119
#if !defined (LSI_VALUE)
120
#define LSI_VALUE ((uint32_t)32000U)
/*!< LSI Typical Value in Hz*/
121
#endif
/* LSI_VALUE */
/*!< Value of the Internal Low Speed oscillator in Hz
122
The real value may vary depending on the variations
123
in voltage and temperature.*/
124
/**
125
* @brief External Low Speed oscillator (LSE) value.
126
*/
127
#if !defined (LSE_VALUE)
128
#define LSE_VALUE ((uint32_t)32768U)
/*!< Value of the External Low Speed oscillator in Hz */
129
#endif
/* LSE_VALUE */
130
131
#if !defined (LSE_STARTUP_TIMEOUT)
132
#define LSE_STARTUP_TIMEOUT ((uint32_t)5000U)
/*!< Time out for LSE start up, in ms */
133
#endif
/* LSE_STARTUP_TIMEOUT */
134
135
/**
136
* @brief External clock source for I2S peripheral
137
* This value is used by the I2S HAL module to compute the I2S clock source
138
* frequency, this source is inserted directly through I2S_CKIN pad.
139
*/
140
#if !defined (EXTERNAL_CLOCK_VALUE)
141
#define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U)
/*!< Value of the External audio frequency in Hz*/
142
#endif
/* EXTERNAL_CLOCK_VALUE */
143
144
/* Tip: To avoid modifying this file each time you need to use different HSE,
145
=== you can define the HSE value in your toolchain compiler preprocessor. */
146
147
/* ########################### System Configuration ######################### */
148
/**
149
* @brief This is the HAL system configuration section
150
*/
151
#define VDD_VALUE ((uint32_t)3300U)
/*!< Value of VDD in mv */
152
#define TICK_INT_PRIORITY ((uint32_t)0U)
/*!< tick interrupt priority */
153
#define USE_RTOS 0U
154
#define PREFETCH_ENABLE 1U
155
#define INSTRUCTION_CACHE_ENABLE 1U
156
#define DATA_CACHE_ENABLE 1U
157
158
#define USE_HAL_ADC_REGISTER_CALLBACKS 0U
/* ADC register callback disabled */
159
#define USE_HAL_CAN_REGISTER_CALLBACKS 0U
/* CAN register callback disabled */
160
#define USE_HAL_CEC_REGISTER_CALLBACKS 0U
/* CEC register callback disabled */
161
#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U
/* CRYP register callback disabled */
162
#define USE_HAL_DAC_REGISTER_CALLBACKS 0U
/* DAC register callback disabled */
163
#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U
/* DCMI register callback disabled */
164
#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U
/* DFSDM register callback disabled */
165
#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U
/* DMA2D register callback disabled */
166
#define USE_HAL_DSI_REGISTER_CALLBACKS 0U
/* DSI register callback disabled */
167
#define USE_HAL_ETH_REGISTER_CALLBACKS 0U
/* ETH register callback disabled */
168
#define USE_HAL_HASH_REGISTER_CALLBACKS 0U
/* HASH register callback disabled */
169
#define USE_HAL_HCD_REGISTER_CALLBACKS 0U
/* HCD register callback disabled */
170
#define USE_HAL_I2C_REGISTER_CALLBACKS 0U
/* I2C register callback disabled */
171
#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U
/* FMPI2C register callback disabled */
172
#define USE_HAL_I2S_REGISTER_CALLBACKS 0U
/* I2S register callback disabled */
173
#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U
/* IRDA register callback disabled */
174
#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U
/* LPTIM register callback disabled */
175
#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U
/* LTDC register callback disabled */
176
#define USE_HAL_MMC_REGISTER_CALLBACKS 0U
/* MMC register callback disabled */
177
#define USE_HAL_NAND_REGISTER_CALLBACKS 0U
/* NAND register callback disabled */
178
#define USE_HAL_NOR_REGISTER_CALLBACKS 0U
/* NOR register callback disabled */
179
#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U
/* PCCARD register callback disabled */
180
#define USE_HAL_PCD_REGISTER_CALLBACKS 0U
/* PCD register callback disabled */
181
#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U
/* QSPI register callback disabled */
182
#define USE_HAL_RNG_REGISTER_CALLBACKS 0U
/* RNG register callback disabled */
183
#define USE_HAL_RTC_REGISTER_CALLBACKS 0U
/* RTC register callback disabled */
184
#define USE_HAL_SAI_REGISTER_CALLBACKS 0U
/* SAI register callback disabled */
185
#define USE_HAL_SD_REGISTER_CALLBACKS 0U
/* SD register callback disabled */
186
#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U
/* SMARTCARD register callback disabled */
187
#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U
/* SDRAM register callback disabled */
188
#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U
/* SRAM register callback disabled */
189
#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U
/* SPDIFRX register callback disabled */
190
#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U
/* SMBUS register callback disabled */
191
#define USE_HAL_SPI_REGISTER_CALLBACKS 0U
/* SPI register callback disabled */
192
#define USE_HAL_TIM_REGISTER_CALLBACKS 0U
/* TIM register callback disabled */
193
#define USE_HAL_UART_REGISTER_CALLBACKS 0U
/* UART register callback disabled */
194
#define USE_HAL_USART_REGISTER_CALLBACKS 0U
/* USART register callback disabled */
195
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U
/* WWDG register callback disabled */
196
197
/* ########################## Assert Selection ############################## */
198
/**
199
* @brief Uncomment the line below to expanse the "assert_param" macro in the
200
* HAL drivers code
201
*/
202
/* #define USE_FULL_ASSERT 1U */
203
204
/* ################## Ethernet peripheral configuration ##################### */
205
206
/* Section 1 : Ethernet peripheral configuration */
207
208
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
209
#define MAC_ADDR0 2U
210
#define MAC_ADDR1 0U
211
#define MAC_ADDR2 0U
212
#define MAC_ADDR3 0U
213
#define MAC_ADDR4 0U
214
#define MAC_ADDR5 0U
215
216
/* Definition of the Ethernet driver buffers size and count */
217
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE
/* buffer size for receive */
218
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE
/* buffer size for transmit */
219
#define ETH_RXBUFNB ((uint32_t)4U)
/* 4 Rx buffers of size ETH_RX_BUF_SIZE */
220
#define ETH_TXBUFNB ((uint32_t)4U)
/* 4 Tx buffers of size ETH_TX_BUF_SIZE */
221
222
/* Section 2: PHY configuration section */
223
224
/* LAN8742A_PHY_ADDRESS Address*/
225
#define LAN8742A_PHY_ADDRESS 0U
226
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
227
#define PHY_RESET_DELAY ((uint32_t)0x000000FFU)
228
/* PHY Configuration delay */
229
#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU)
230
231
#define PHY_READ_TO ((uint32_t)0x0000FFFFU)
232
#define PHY_WRITE_TO ((uint32_t)0x0000FFFFU)
233
234
/* Section 3: Common PHY Registers */
235
236
#define PHY_BCR ((uint16_t)0x00U)
/*!< Transceiver Basic Control Register */
237
#define PHY_BSR ((uint16_t)0x01U)
/*!< Transceiver Basic Status Register */
238
239
#define PHY_RESET ((uint16_t)0x8000U)
/*!< PHY Reset */
240
#define PHY_LOOPBACK ((uint16_t)0x4000U)
/*!< Select loop-back mode */
241
#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U)
/*!< Set the full-duplex mode at 100 Mb/s */
242
#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U)
/*!< Set the half-duplex mode at 100 Mb/s */
243
#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U)
/*!< Set the full-duplex mode at 10 Mb/s */
244
#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U)
/*!< Set the half-duplex mode at 10 Mb/s */
245
#define PHY_AUTONEGOTIATION ((uint16_t)0x1000U)
/*!< Enable auto-negotiation function */
246
#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U)
/*!< Restart auto-negotiation function */
247
#define PHY_POWERDOWN ((uint16_t)0x0800U)
/*!< Select the power down mode */
248
#define PHY_ISOLATE ((uint16_t)0x0400U)
/*!< Isolate PHY from MII */
249
250
#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U)
/*!< Auto-Negotiation process completed */
251
#define PHY_LINKED_STATUS ((uint16_t)0x0004U)
/*!< Valid link established */
252
#define PHY_JABBER_DETECTION ((uint16_t)0x0002U)
/*!< Jabber condition detected */
253
254
/* Section 4: Extended PHY Registers */
255
#define PHY_SR ((uint16_t)0x1FU)
/*!< PHY status register Offset */
256
257
#define PHY_SPEED_STATUS ((uint16_t)0x0004U)
/*!< PHY Speed mask */
258
#define PHY_DUPLEX_STATUS ((uint16_t)0x0010U)
/*!< PHY Duplex mask */
259
260
#define PHY_ISFR ((uint16_t)0x001DU)
/*!< PHY Interrupt Source Flag register Offset */
261
#define PHY_ISFR_INT4 ((uint16_t)0x000BU)
/*!< PHY Link down inturrupt */
262
263
/* ################## SPI peripheral configuration ########################## */
264
265
/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
266
* Activated: CRC code is present inside driver
267
* Deactivated: CRC code cleaned from driver
268
*/
269
270
#define USE_SPI_CRC 0U
271
272
/* Includes ------------------------------------------------------------------*/
273
/**
274
* @brief Include module's header file
275
*/
276
277
#ifdef HAL_RCC_MODULE_ENABLED
278
#include "stm32f4xx_hal_rcc.h"
279
#endif
/* HAL_RCC_MODULE_ENABLED */
280
281
#ifdef HAL_GPIO_MODULE_ENABLED
282
#include "stm32f4xx_hal_gpio.h"
283
#endif
/* HAL_GPIO_MODULE_ENABLED */
284
285
#ifdef HAL_EXTI_MODULE_ENABLED
286
#include "stm32f4xx_hal_exti.h"
287
#endif
/* HAL_EXTI_MODULE_ENABLED */
288
289
#ifdef HAL_DMA_MODULE_ENABLED
290
#include "stm32f4xx_hal_dma.h"
291
#endif
/* HAL_DMA_MODULE_ENABLED */
292
293
#ifdef HAL_CORTEX_MODULE_ENABLED
294
#include "stm32f4xx_hal_cortex.h"
295
#endif
/* HAL_CORTEX_MODULE_ENABLED */
296
297
#ifdef HAL_ADC_MODULE_ENABLED
298
#include "stm32f4xx_hal_adc.h"
299
#endif
/* HAL_ADC_MODULE_ENABLED */
300
301
#ifdef HAL_CAN_MODULE_ENABLED
302
#include "stm32f4xx_hal_can.h"
303
#endif
/* HAL_CAN_MODULE_ENABLED */
304
305
#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
306
#include "stm32f4xx_hal_can_legacy.h"
307
#endif
/* HAL_CAN_LEGACY_MODULE_ENABLED */
308
309
#ifdef HAL_CRC_MODULE_ENABLED
310
#include "stm32f4xx_hal_crc.h"
311
#endif
/* HAL_CRC_MODULE_ENABLED */
312
313
#ifdef HAL_CRYP_MODULE_ENABLED
314
#include "stm32f4xx_hal_cryp.h"
315
#endif
/* HAL_CRYP_MODULE_ENABLED */
316
317
#ifdef HAL_DMA2D_MODULE_ENABLED
318
#include "stm32f4xx_hal_dma2d.h"
319
#endif
/* HAL_DMA2D_MODULE_ENABLED */
320
321
#ifdef HAL_DAC_MODULE_ENABLED
322
#include "stm32f4xx_hal_dac.h"
323
#endif
/* HAL_DAC_MODULE_ENABLED */
324
325
#ifdef HAL_DCMI_MODULE_ENABLED
326
#include "stm32f4xx_hal_dcmi.h"
327
#endif
/* HAL_DCMI_MODULE_ENABLED */
328
329
#ifdef HAL_ETH_MODULE_ENABLED
330
#include "stm32f4xx_hal_eth.h"
331
#endif
/* HAL_ETH_MODULE_ENABLED */
332
333
#ifdef HAL_FLASH_MODULE_ENABLED
334
#include "
stm32f4xx_hal_flash.h
"
335
#endif
/* HAL_FLASH_MODULE_ENABLED */
336
337
#ifdef HAL_SRAM_MODULE_ENABLED
338
#include "stm32f4xx_hal_sram.h"
339
#endif
/* HAL_SRAM_MODULE_ENABLED */
340
341
#ifdef HAL_NOR_MODULE_ENABLED
342
#include "stm32f4xx_hal_nor.h"
343
#endif
/* HAL_NOR_MODULE_ENABLED */
344
345
#ifdef HAL_NAND_MODULE_ENABLED
346
#include "stm32f4xx_hal_nand.h"
347
#endif
/* HAL_NAND_MODULE_ENABLED */
348
349
#ifdef HAL_PCCARD_MODULE_ENABLED
350
#include "stm32f4xx_hal_pccard.h"
351
#endif
/* HAL_PCCARD_MODULE_ENABLED */
352
353
#ifdef HAL_SDRAM_MODULE_ENABLED
354
#include "stm32f4xx_hal_sdram.h"
355
#endif
/* HAL_SDRAM_MODULE_ENABLED */
356
357
#ifdef HAL_HASH_MODULE_ENABLED
358
#include "stm32f4xx_hal_hash.h"
359
#endif
/* HAL_HASH_MODULE_ENABLED */
360
361
#ifdef HAL_I2C_MODULE_ENABLED
362
#include "stm32f4xx_hal_i2c.h"
363
#endif
/* HAL_I2C_MODULE_ENABLED */
364
365
#ifdef HAL_SMBUS_MODULE_ENABLED
366
#include "stm32f4xx_hal_smbus.h"
367
#endif
/* HAL_SMBUS_MODULE_ENABLED */
368
369
#ifdef HAL_I2S_MODULE_ENABLED
370
#include "stm32f4xx_hal_i2s.h"
371
#endif
/* HAL_I2S_MODULE_ENABLED */
372
373
#ifdef HAL_IWDG_MODULE_ENABLED
374
#include "stm32f4xx_hal_iwdg.h"
375
#endif
/* HAL_IWDG_MODULE_ENABLED */
376
377
#ifdef HAL_LTDC_MODULE_ENABLED
378
#include "stm32f4xx_hal_ltdc.h"
379
#endif
/* HAL_LTDC_MODULE_ENABLED */
380
381
#ifdef HAL_PWR_MODULE_ENABLED
382
#include "stm32f4xx_hal_pwr.h"
383
#endif
/* HAL_PWR_MODULE_ENABLED */
384
385
#ifdef HAL_RNG_MODULE_ENABLED
386
#include "stm32f4xx_hal_rng.h"
387
#endif
/* HAL_RNG_MODULE_ENABLED */
388
389
#ifdef HAL_RTC_MODULE_ENABLED
390
#include "stm32f4xx_hal_rtc.h"
391
#endif
/* HAL_RTC_MODULE_ENABLED */
392
393
#ifdef HAL_SAI_MODULE_ENABLED
394
#include "stm32f4xx_hal_sai.h"
395
#endif
/* HAL_SAI_MODULE_ENABLED */
396
397
#ifdef HAL_SD_MODULE_ENABLED
398
#include "stm32f4xx_hal_sd.h"
399
#endif
/* HAL_SD_MODULE_ENABLED */
400
401
#ifdef HAL_SPI_MODULE_ENABLED
402
#include "stm32f4xx_hal_spi.h"
403
#endif
/* HAL_SPI_MODULE_ENABLED */
404
405
#ifdef HAL_TIM_MODULE_ENABLED
406
#include "stm32f4xx_hal_tim.h"
407
#endif
/* HAL_TIM_MODULE_ENABLED */
408
409
#ifdef HAL_UART_MODULE_ENABLED
410
#include "stm32f4xx_hal_uart.h"
411
#endif
/* HAL_UART_MODULE_ENABLED */
412
413
#ifdef HAL_USART_MODULE_ENABLED
414
#include "stm32f4xx_hal_usart.h"
415
#endif
/* HAL_USART_MODULE_ENABLED */
416
417
#ifdef HAL_IRDA_MODULE_ENABLED
418
#include "stm32f4xx_hal_irda.h"
419
#endif
/* HAL_IRDA_MODULE_ENABLED */
420
421
#ifdef HAL_SMARTCARD_MODULE_ENABLED
422
#include "stm32f4xx_hal_smartcard.h"
423
#endif
/* HAL_SMARTCARD_MODULE_ENABLED */
424
425
#ifdef HAL_WWDG_MODULE_ENABLED
426
#include "stm32f4xx_hal_wwdg.h"
427
#endif
/* HAL_WWDG_MODULE_ENABLED */
428
429
#ifdef HAL_PCD_MODULE_ENABLED
430
#include "stm32f4xx_hal_pcd.h"
431
#endif
/* HAL_PCD_MODULE_ENABLED */
432
433
#ifdef HAL_HCD_MODULE_ENABLED
434
#include "stm32f4xx_hal_hcd.h"
435
#endif
/* HAL_HCD_MODULE_ENABLED */
436
437
#ifdef HAL_DSI_MODULE_ENABLED
438
#include "stm32f4xx_hal_dsi.h"
439
#endif
/* HAL_DSI_MODULE_ENABLED */
440
441
#ifdef HAL_QSPI_MODULE_ENABLED
442
#include "stm32f4xx_hal_qspi.h"
443
#endif
/* HAL_QSPI_MODULE_ENABLED */
444
445
#ifdef HAL_CEC_MODULE_ENABLED
446
#include "stm32f4xx_hal_cec.h"
447
#endif
/* HAL_CEC_MODULE_ENABLED */
448
449
#ifdef HAL_FMPI2C_MODULE_ENABLED
450
#include "stm32f4xx_hal_fmpi2c.h"
451
#endif
/* HAL_FMPI2C_MODULE_ENABLED */
452
453
#ifdef HAL_SPDIFRX_MODULE_ENABLED
454
#include "stm32f4xx_hal_spdifrx.h"
455
#endif
/* HAL_SPDIFRX_MODULE_ENABLED */
456
457
#ifdef HAL_DFSDM_MODULE_ENABLED
458
#include "stm32f4xx_hal_dfsdm.h"
459
#endif
/* HAL_DFSDM_MODULE_ENABLED */
460
461
#ifdef HAL_LPTIM_MODULE_ENABLED
462
#include "stm32f4xx_hal_lptim.h"
463
#endif
/* HAL_LPTIM_MODULE_ENABLED */
464
465
#ifdef HAL_MMC_MODULE_ENABLED
466
#include "stm32f4xx_hal_mmc.h"
467
#endif
/* HAL_MMC_MODULE_ENABLED */
468
469
/* Exported macro ------------------------------------------------------------*/
470
#ifdef USE_FULL_ASSERT
471
/**
472
* @brief The assert_param macro is used for function's parameters check.
473
* @param expr If expr is false, it calls assert_failed function
474
* which reports the name of the source file and the source
475
* line number of the call that failed.
476
* If expr is true, it returns no value.
477
* @retval None
478
*/
479
#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
480
/* Exported functions ------------------------------------------------------- */
481
void
assert_failed(uint8_t* file, uint32_t line);
482
#else
483
#define assert_param(expr) ((void)0U)
484
#endif
/* USE_FULL_ASSERT */
485
486
#ifdef __cplusplus
487
}
488
#endif
489
490
#endif
/* __STM32F4xx_HAL_CONF_H */
491
492
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
stm32f4xx_hal_flash.h
Header file of FLASH HAL module.
Generated on Sat Sep 27 2025 00:10:07 for rusEFI by
1.9.8
1.9.8